1. If you have recently registered with a gmail email address, you must contact me, as gmail will not forward our confirmation email to you. Contact me and jim@trishieldperformance.com to complete your registration.
    Dismiss Notice
  2. In and effort to reduce the spam on the site, several years ago I had went to a program where I manually approve each and every new registration. This approval gives you full access to the site, to pictures, and to post, among other things. To be able to enjoy the full potential of the board for you, you need to be fully registered.. and that's easy.. Just send an email to me at jim@trishieldperformance.com and I will verify your registration. This policy will remain in effect indefinitely, as it has completely eliminated the bad actors from our site, who would spam and hack it, once they gained access. Thanks JW
    Dismiss Notice
  3. The "Group Buy" for the 1967-68 Deluxe Steering wheel recasting is now officially "Open". Now is the time to start sending in the wheels. The latest date that the wheels must be received by Kochs is 31 March 2025 The cost for each wheel is $750. The only "up front cost" is your shipping the wheel. If you send in more than one wheel, each additional wheel will cost $700. Shipping and insurance to Kochs and return shipping will be extra. You will be contacted by Teresa to make payment for the wheel(s) and return shipping and insurance when your wheel(s) is complete. The shipping will be factored on your delivery address and insurance. I will be sending the contact information all of you have sent me to Teresa at Kochs. Send in your wheels, horn pad and hardware and paint color sample if applicable. Please include: First and Last Name Shipping Address Phone number email address V8Buick "Member Name" Wheel Color (SEE THE BOTTOM FOR WHEEL COLOR) Pease read the "shipping to Kochs" below. There are two addresses. One for USPS Mailing One for FedEx and UPS shipping You can use USPS/Mail, UPS or FedEx to send in your core. Use the appropriate address depending on what service you use to ship. If you use USPS/Mail ship to: Koch's P.O. Box 959 Acton, CA 93510 Attn: Teresa If you use UPS or FedEx ship to: Koch's 7650 Soledad Canyon Road Acton CA 93510 Attn: Teresa Kochs Contact: Teresa (661) 268-1341 customerservice@kochs.com Wheel Color If you wheel is Black, you can list that in your information you send in with your wheel. For colored wheels, please contact Teresa about specifics for wheel color if you do not send in a color sample to match. Please contact me if you have any questions. Thank you to everyone for your participation in making this a reality. And "Thank You" Jim Weise, for allowing and facilitating this project! Michael .................... to remove this notice, click the X in the upper RH corner of this message box
    Dismiss Notice

Needed. Big, Thick Super T-10 yoke

Discussion in 'Parts wanted' started by Floydsbuick, Sep 4, 2005.

  1. Floydsbuick

    Floydsbuick Well-Known Member

    I put the super T-10 in my Regal last month. My Turbo 400 yoke was the same spline, but not thick enough in diameter for the ST-10 rear bushing and seal. Thus, I am using a borrowed one. I need to get another for the dude I borrowed it off of. So thats it, I need the big, thick, Super T-10 yoke. Thanks!
     
  2. DRS4554

    DRS4554 Well-Known Member

    That yolk is not Super T-10 specific. Some TH400's use the large o.d. yolk too. From what I've seen the small o.d. yolk's seem to have been used in the cars with a two piece drive shaft with a carrier bearing and the large o.d. yolk's were in cars with a one piece drive shaft. That's just been my experiance. No guarantee they were all that way. My point is, don't narrow your search to just Super T-10's. Good luck.
     
  3. Stage2Scott

    Stage2Scott Well-Known Member

    in your area....

    call john kunsak--724-935-5613 after 11 am most days. he likely ahs what you need. tell him scott in california sent ya. :Comp:
     
  4. evil16v

    evil16v Midwest Buick Mafia

    that may be a long shaft th 400 yoke... my 67 bu trans (short shaft) from a lesabre is one of the small O.D. yokes i had a long shaft yoke that would not fit it, becuse of th large O.D. you may just need a long shaft th400 yoke... those grow on trees!
     
  5. Floydsbuick

    Floydsbuick Well-Known Member

    I really dunno what 400s had em or not. All my Wildcat ones are small girth from longshaft 400s and one-piece driveshafts. The yoke I'm using was in the back of a Chevy TH400.

    Scott,

    I'll call him this week. Thanks.
     

Share This Page