Need Parts For 1967 Gs Conv. 400

Discussion in 'Parts wanted' started by geno, Aug 19, 2005.

  1. geno

    geno Founders Club Member

    I NEED CENTER CAPS FOR 14/6 RIMS I DON,T KNOW IF THEY WERE BIRDS OR BUICK TRY SHEILD THAT YEAR NEED REMOUT MIRROW FOR DRIVERS DOOR WOULD LIKE TO FIND TACK THAT FITS IN CONSUL NEED PART # for metal gasket that fits between both fiber gaskets on intake for 401 with quad or a gasket THANKS FOR ANY HELP IN FINDING PARTS GENO
     
  2. MY3BUICKS

    MY3BUICKS Guest

    repop

    The centers are reproduced, Mitch Romanowski has them 847-705-5761 - they are very nice!!- it would take tri-shields
     
  3. geno

    geno Founders Club Member

    67 Parts

    THANK YOU FOR INF. on caps geno
     
  4. banburi

    banburi Well-Known Member

    67 Parts

    Do you have a 401 in the 67? The 67's GS had a 340 or 400, factory engine.
    Michael Dyer
     
  5. geno

    geno Founders Club Member

    Motor Size

    I Have A Gs 400 I Thought It Was A 400 People Tell Me It Was A 401 In 67 I Bought It New In 67 From A Buick Dealer People Ask Me If It A Nailhead I Can,t Tell The Differance When I Ordered Plug Wires For A 400 They Were To Short I Ordered Wires For A Nailhead They Fit It Has Air Cleaner Like Starwars I Had To Ordered Filter For Nail Head It Fit How Can I Tell Geno
     
  6. banburi

    banburi Well-Known Member

    ID of 400

    Easy enough to ID. The nailheads among other things were mostly blue/green in color, the 400's were red. The casting number on your manifold will tell as well as the block casting #. Post either and we'll identify for you. You bought it new in 67 & Starwars aircleaner = 400. Look at the 400 pictures on my website, prior to my changing manifolds/carb/exhaust.
    www.67gs400.com
    Michael Dyer
     
  7. landshark

    landshark gearhead, railfan, maniac

    The valve covers on a nailhead sit on a horizontal plane, as though you took them off and laid them on a table. The 67 400 valve covers sit at about a 45 degree angle, like most V8s. Rich
     
  8. Nailhead valve covers have 2 bolts in the middle of the valve cover that hold them down. a 400 will have 5 boltsd on each valve cover. 2 on the top or intake side and 2 on the bottom or exhaust manifold side. also a nailhead has a distributor in the rear and a 400 has the distributor in the front. Bob
     
  9. geno

    geno Founders Club Member

    Id On Motor

    ITS A 400 valve covers are on 45 ALSO MOTOR WAS RED DIS. IS IN FRONT I WILL BE BUYING CAPS FROM MITCH I STILL CAN,T FIND METAL GASKET THAT GOES BETWEEN TO FIBER GASKETS UNDER QUAD CARB MY IS RUSTED OUT REAL BAD PERSON THAT REDID MY CARB SAYS WE CANN,T RUN WITH OUT IT WOULD LIKE TO FIND TACK AND MIROW FOR THAT YEAR CAR FOR DRIVERS DOOR GENO
     
  10. Blaze333

    Blaze333 Craig B.

    How much you pay for centers?
    I'm looking for a set too.
    Thanks
     
  11. geno

    geno Founders Club Member

    Center Caps

    For Set Of Four With Shipping And Ins. These Are Trysheild Reproduced 170.00 They Are Asking The Same Amount For Oring. Once That Need To Be Chromed Gene :)
     

Share This Page