1. If you have recently registered with a gmail email address, you must contact me, as gmail will not forward our confirmation email to you. Contact me and jim@trishieldperformance.com to complete your registration.
    Dismiss Notice
  2. In and effort to reduce the spam on the site, several years ago I had went to a program where I manually approve each and every new registration. This approval gives you full access to the site, to pictures, and to post, among other things. To be able to enjoy the full potential of the board for you, you need to be fully registered.. and that's easy.. Just send an email to me at jim@trishieldperformance.com and I will verify your registration. This policy will remain in effect indefinitely, as it has completely eliminated the bad actors from our site, who would spam and hack it, once they gained access. Thanks JW
    Dismiss Notice
  3. The "Group Buy" for the 1967-68 Deluxe Steering wheel recasting is now officially "Open". Now is the time to start sending in the wheels. The latest date that the wheels must be received by Kochs is 31 March 2025 The cost for each wheel is $750. The only "up front cost" is your shipping the wheel. If you send in more than one wheel, each additional wheel will cost $700. Shipping and insurance to Kochs and return shipping will be extra. You will be contacted by Teresa to make payment for the wheel(s) and return shipping and insurance when your wheel(s) is complete. The shipping will be factored on your delivery address and insurance. I will be sending the contact information all of you have sent me to Teresa at Kochs. Send in your wheels, horn pad and hardware and paint color sample if applicable. Please include: First and Last Name Shipping Address Phone number email address V8Buick "Member Name" Wheel Color (SEE THE BOTTOM FOR WHEEL COLOR) Pease read the "shipping to Kochs" below. There are two addresses. One for USPS Mailing One for FedEx and UPS shipping You can use USPS/Mail, UPS or FedEx to send in your core. Use the appropriate address depending on what service you use to ship. If you use USPS/Mail ship to: Koch's P.O. Box 959 Acton, CA 93510 Attn: Teresa If you use UPS or FedEx ship to: Koch's 7650 Soledad Canyon Road Acton CA 93510 Attn: Teresa Kochs Contact: Teresa (661) 268-1341 customerservice@kochs.com Wheel Color If you wheel is Black, you can list that in your information you send in with your wheel. For colored wheels, please contact Teresa about specifics for wheel color if you do not send in a color sample to match. Please contact me if you have any questions. Thank you to everyone for your participation in making this a reality. And "Thank You" Jim Weise, for allowing and facilitating this project! Michael .................... to remove this notice, click the X in the upper RH corner of this message box
    Dismiss Notice

Buick 455 Rods

Discussion in 'Parts wanted' started by ronbz455, Mar 16, 2013.

  1. ronbz455

    ronbz455 Big Butz Racing

    I'm looking for a set of aftermarket rods for BBB. I would like direct fit or Pontiac aftermarket rods already machined to fit.
    I'm going to freshen up the 455 in the GS that I race and might put flat tops in it.
     

    Attached Files:

  2. killrbuick66455

    killrbuick66455 Well-Known Member

    how about a set of these
     

    Attached Files:

  3. killrbuick66455

    killrbuick66455 Well-Known Member

    If your interested I have these also
     

    Attached Files:

  4. ronbz455

    ronbz455 Big Butz Racing

    why is the small hole smaller than an 1.0? Is that the way the pins are sized in those pistons? The big end size is without bearing installed?
    Tell me your story on that combo.
     
  5. killrbuick66455

    killrbuick66455 Well-Known Member

    These are parts I've collected over the years These parts were never together in a engine. I'm going into a different direction. I want build a 470 and don't need these parts.
     
  6. ronbz455

    ronbz455 Big Butz Racing

    So the rods have never been used?
     
  7. ronbz455

    ronbz455 Big Butz Racing

    What brand pistons and what width rings?
     
  8. killrbuick66455

    killrbuick66455 Well-Known Member

    There Ross racing Pistons 12.5 to 1 depending on heads and head gaskets These are brand new never used.. The rods are used bought them off a board member 8 years ago..Ill look to see what rings they have.. I've just looked there's no info on ring size.
     
  9. ronbz455

    ronbz455 Big Butz Racing

    Don't worry about the rods they are too heavy. I will think about the pistons.
     
  10. killrbuick66455

    killrbuick66455 Well-Known Member

    Ok sounds good Ron
     
  11. ronbz455

    ronbz455 Big Butz Racing

    Are those pistons full floating? Do you have the locks and pins? How much do you need to get out of them?
     
  12. staged70

    staged70 RIP

    I have a set of SD pont rods if your interested but I realize they are not after market and slightly longer than Stock BBB
     
  13. killrbuick66455

    killrbuick66455 Well-Known Member

    Hey Ron,Yes there full floating I would like to get 475.00 + the ride let me know if that sounds good..
     
  14. ronbz455

    ronbz455 Big Butz Racing

    I found another set like yours for 400 but I have to sell my Ross pistons first that don't have as big of valve reliefs in them. I will keep yours in mind.
     
  15. killrbuick66455

    killrbuick66455 Well-Known Member

    OK Ron sounds good Thanks for the reply
     
  16. ronbz455

    ronbz455 Big Butz Racing

    I need to know the ring width or thickness. 1/16 or 5/64th.
     
  17. nickbuickgs

    nickbuickgs nickbuickgs

    I have a used set Pontiac length 6.625
     
  18. ronbz455

    ronbz455 Big Butz Racing

    H beam or stock?
     
  19. ronbz455

    ronbz455 Big Butz Racing

    Has anyone used those TA sportsman rods for $800? Is there any way of getting them cheaper than that?
     
  20. 300sbb_overkill

    300sbb_overkill WWG1WGA. MAGA

    Ron,did you find rods yet?


    Derek
     

Share This Page