Turn Signal cam #

Discussion in 'Sparky's corner' started by 65WILDKAT, Mar 14, 2006.

  1. 65WILDKAT

    65WILDKAT A PROUD FATHER OF THREE!

    Does anone have the GM # for the turn signal cam for a 65 Wildcat? Where can I get one? Mine is broken and I can't find any #'s on it. What other Model does it cross referece with, I was thinking a Riv or even a Impala of the same year?
    Thanks in advance,
    Don
     
  2. dualqwad

    dualqwad ...just another lost soul

    Group #2.896 Part #384025 cam :Smarty:
    Parts book shows it the same for Skylark, LeSabre, and Electra too. :TU:
     
  3. 65WILDKAT

    65WILDKAT A PROUD FATHER OF THREE!

    Thank you

    Robert,
    Thank you! What book did you get that from?
    Don
     
  4. flynbuick

    flynbuick Guest

    Cam including contact ring less tilt all 64-66 series Buicks GM #382931
     
  5. dualqwad

    dualqwad ...just another lost soul

    This one...
     

    Attached Files:

  6. 65WILDKAT

    65WILDKAT A PROUD FATHER OF THREE!

    Where do you find them?

    I need a Book like that! Thanks for the help, Now if I can just find a switch :Brow: This is the hard part of the Hobby, I would have thought that GM. would have made them all the same so that all the different lines of cars Pontiac, Olds, Buick, Chevy, would have made better sense in the cost effectiveness? :confused: .
    Don
     
  7. 65WILDKAT

    65WILDKAT A PROUD FATHER OF THREE!

    Part I Need

    This what I am looking for, Can any one HELP ME? I need to pass inspection
    Don
     

    Attached Files:

  8. 2manybuicks

    2manybuicks Founders Club Member

    Saw a 65 or 66 Cat (with power buckets!) in the yard in Fort Lauderdale as I did a swing-by late Tuesday. No time to pull parts, though.

    I will check on Saturday. Can pull the buckets cheap too if anyone is interested and if they are still there.

    -- Steve
     
  9. 65WILDKAT

    65WILDKAT A PROUD FATHER OF THREE!

    That Would Be Great!

    STEVE,
    THAT WOULD BE VERY KND OF YOU IF YOU COULD DO THAT FOR ME!
    :TU: :TU: :TU: I would be a very happy man, Also see if they have VENT WINDOW REGULATORS ALSO??? If that is not asking to much of your time?
    I would be very grateful, My car is due for Inspection at the end of April.
    A VERY HUMBLE,
    Don
     
  10. 2manybuicks

    2manybuicks Founders Club Member

    When I was there the steering wheel was still in place, it was definitely a non-tilt column. So it will most likely be there. Qustion is whether it will be any good or not.

    Vent window regulators -- you mean electric?

    -- Steve
     
  11. 65WILDKAT

    65WILDKAT A PROUD FATHER OF THREE!

    No, Crank type

    Steve,
    I need the mechanical type, The type that you need to crank open by hand.
    Thanks so much,
    Don
     
  12. dualqwad

    dualqwad ...just another lost soul

    If the vents ARE electric then I'll take them; wiring, switches with door panel anchors too! :Brow:
     
  13. telriv

    telriv Founders Club Member

    I have a '66 Wildcat I'm parting out that has those parts. E-mail me off list.

    Tom T.
     
  14. 65WILDKAT

    65WILDKAT A PROUD FATHER OF THREE!

    Side of Switch

    A Fuzzy side shot of switch, The plate is part of the switch they are riveted to each other and the wires go down into the plug near floor
     

    Attached Files:

  15. 2manybuicks

    2manybuicks Founders Club Member

    Don --

    No luck on the switch last weekend -- couldn't get the durn wheel to pop. Will go back this weekend. Switch at least clicked in place like it should.

    Driver's manual vent window regulator had the outer side popped out, so it was not operational, though you could possibly repair it. Gears were fine.

    Passenger side manual vent window regulator had the bottom popped out, but it worked. Could re-install the bottom, or just use two to make one good one. Gears were also fine.

    Probably best off tlking to telriv for the regulators.

    -- Steve
     
  16. 65WILDKAT

    65WILDKAT A PROUD FATHER OF THREE!

    Don't worry about it

    Steve,
    Don't worry about it! I got a line on a switch! :grin: , I also think that I found a place to get the regulators! Thank you anyway! :TU:
    Don
     
  17. TXCruiser

    TXCruiser Member

    M&H Electric has 'em - new

    These guys manufacture a variety of switches and electrical parts. I just got a turn signal switch from them to fix my intermittent horn problem, but I haven't installed it yet. It appears to be an exact match though.

    http://www.wiringharness.com/
     

Share This Page