GSX Rear Spoiler Hardware

Discussion in 'Parts wanted' started by IDOXLR8, Jan 7, 2022.

  1. IDOXLR8

    IDOXLR8 Senior Member

    Looking for all the hardware to correctly install the rear spoiler on a 1972 GSX.
     
  2. STAGE III

    STAGE III Lost Experimental 455-4 Bolt Main Block.

    They aren’t correct but repops are out there,took me years to find my NOS ones.
     
  3. CJay

    CJay Supercar owner Staff Member

    Contact Todd at stage1restoration.com. he has it all in stock
     
    bamboo72 and ToddsGS like this.
  4. ToddsGS

    ToddsGS Founders Club Member

    I spent a lot of hours with GSX owners to get what is considered correct for GSX Spoiler Hardware . . . . .

    I offer a few variations depending on what each customer needs and as you can see from the photos I offer front & rear Kits. You WON'T find any hardware for Spoilers more correct than what I offer!



    This Kit is Front Spoiler & Baffle Hardware. . .
    BuickFrontSpoiler_BaffleHardwareKit.jpg


    Baffle Only . . .
    BuickFrontSpoilerBaffleHardware.jpg


    Factory Bulletin from Buick . . . . As you'll see here the kit calls for 1" Washers and Locking Nuts as well. My kit includes BOTH! :)
    BuickFrontSpoilerBulletin.jpg


    Front Spoiler Only Hardware
    BuickFrontSpoilerHardware.jpg


    This Kit includes the Brace also . . .
    BuickFrontSpoilerHardware_Brace.jpg

    BuickFrontSpoilerMountingSpecs.jpg

    This Kit includes the Brackets if needed. . . .
    BuickRearSpoilerHardware_Brkt.jpg

    Note: This kit includes the factory size hardware. . . . IF your spoiler has had to big of bolts in it at some point these may not work or you'll have to fill the holes and re-drill!!!
    BuickRearSpoilerHardwareKit.jpg



    These Kits are on my Website's Exterior Page Or you can use the Search engine to find them as well. "Search Spoiler Kit"
     
    Last edited: Jan 7, 2022
    STAGE III likes this.
  5. STAGE III

    STAGE III Lost Experimental 455-4 Bolt Main Block.

    Yes, Todd has a tremendous collection of all sorts of beautiful new reproductions that were desperately needed.
    Thank you again Todd for all your tireless work for our merry band of Buick addicts! : )

    Sincerely,
    Fritzenshiftin
     
    ToddsGS likes this.
  6. ToddsGS

    ToddsGS Founders Club Member


    I spend the time to source this stuff because we do a lot of Restorations here (mostly Concours Type stuff) so it makes sense for us to have the right stuff! And by selling it on my website it's a "Win - Win" for everyone!

    Thank you to everyone that has taken the time to visit my website! If you haven't been on my site yet . . . . Check it out, I bet I have more parts that most guys realize! (And adding stuff all the time)


    Thanks Guys! I appreciate the referrals also!! :)



    00001.Stage1RestorationBannerImg_350.jpg
     
    STAGE III and Stage 2 iron like this.
  7. IDOXLR8

    IDOXLR8 Senior Member

    Todd, your kit has four screws, the rear spoiler I have seen use one screw and the other is a stud. ????
     
  8. Smartin

    Smartin antiqueautomotiveservice.com Staff Member

    Those are studs, Al. The silver ones.
     
    ToddsGS likes this.
  9. IDOXLR8

    IDOXLR8 Senior Member

    Oh! I see that now, thanks.
     

Share This Page