350,400,430 and nailhead NOS head gaskets/401 motor-trans ~ (6) #1385204 350 brown hard composite 1pc hd gaskets , gessler site lists them as '68-'69 350 but i took some off of a '75 350 that i took apart . $10 each plus s/h ~ (3) #1384313 ( mc6760 ) 68-69 400 1pc steel hd gaskets . $20 each plus s/h ~ (4) #1373719-1384411 (mc6713-mc6756 ) 68-69 430 1pc steel hd gaskets . $20 each plus s/h ~ plus some older nailhead head gaskets - part #'s 1173567 , 1196917 ( in set #1396543 ) , 1165307 , 1196917 , 1391261 , and 1396603 ( set ) . $10 each plus s/h - #603 set $30 plus s/h thats it . thanks . del a little shop cleaning . all dealings here unless ya need info via e-mail or pm .
hi tom.i think i talked to you at lebanon valley a few years ago in the fall.anyway-i will get that info rounded up and post it asap.thanks.del
tom : here is the nailhead info - NOS , dusty , bore specs are approx 'cause the battery is down in my calipers - ~ (3)#1196917(mccord#6509)steel 3pc sandwich gskt-4 1/4" bore ~ (2)#1173567-supercedes up to the #1196917-handwritten note on this one says "use only on early 1962" -?- looks the same? ~ (2)#1165307-steel 1pc gskt-4 1/8" bore ~ (2)#1371337(mccord#6605)-steel 1pc gskt-4 7/16" bore ----- sale pending - sold ~ (1)#1343995(mccord#6548?)-steel 3pc sandwich gskt-4 3/16" bore ~ (1)#1396543-head gskt set with steel 3 pc sandwich gskts (#1196917/mccord#6509)-4 1/4" bore-includes steel intake gskts,cork v/cover gskts and water crossover gskts. ----- sale pending - sold ~ $10 each , $30 for the head set , $80 all - plus shipping :::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::: also found a new felpro #PS11407R-rubber lifter valley cover gasket and a new felpro #MS9411SH steel intake gasket set - $15 both - plus shipping ----- sale pending / intake set - sold :::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::: fyi-also have a '65 cat 401 engine and switch 400 trans.block is done and bored .030,new cast pistons,crank polished/mag'd and rods beamed/mag'd with arp's and balanced,heads done (new poston hd oil pump,tq converter and bearings),new kb v/springs and spare heads and block and trans and some other parts from a '66.trans was rebuilt by a good local shop.etc etc etc.thats it.probably forgot a few things.$-?.thanks.del @@@@ MORE MOTOR/TRANS INFO IN FOLLOWING POSTS @@@@
Del, if you wouldn't mind splitting it up I will take the two #1371337 gaskets. The one #1396543 head gasket set & the MS9411SH intake gaskets. Send me a $$$ amount & shipping to 06906-1820. I can pay you with a personal check, company check, Visa or a Postal Money Order. Whichever you prefer. Thanks, Tom
robert/tom - will figure all that out tonight when i get home and let ya know the outcome . cost - shipping - etc . thanks . del
first : robert - since tom does not want all the gaskets and you spoke up first for a set of intakes then i guess technically you may have the felpro intake set if you'd like --- but truthfully --- the cost plus shipping (west coast 'bout $9.00) will be a little more than if you just bought the set locally . i checked a couple auto parts web sites and you should be looking at $11 - $14 , it would probably be $15 at least if i shipped to you . tom is east coast and getting other stuff so its not bad that way . second : tom - two steel 1pc #337 gaskets and #543 head set ( reminder - that has 3pc steel sandwich head gaskets not 1 pc steels ) and the felpro intake set ( taking for granted that robert will not take them ) $58 plus shipping ups/ground = $67 ( can do usps , may be a little cheaper but prefer ups ) . if less than that for some reason will refund 'ya . if a little over no problem . postal money order prefered . if thats all ok we can e-mail address info back and forth and we'll be set . thats it . thanks for the look . del
No problem Del. You could even bring them to the spring club meeting at Readers Digest if you plan on going. Tom
tom : no word yet from robert , he'll most likely buy local , so whatever ya wanna do . will pm ya my address and phone# . del
joe : ~ in reply to your pm - if you'd like the rest of the nailhead gaskets and since you'd be cleanin' 'em out for me - $80 and i throw in the fel pro cover gasket and i'll do the shipping . if ya want less we can refigure . ~ i will send ya a list and $$ on the 401/"switch" th400 parts and history as soon as i double check everything . thanks . del
joe : here is 401 info - had it for awhile and really hate to sell but i can use the $$ for other project and its not good for it to just sit around ( lubed and covered ) probably . engine and trans came outa' a nice one owner 60000 mile 65 cat 4 door , nice old guy had it but he left his keys in it one night and neighbor kid took it and ditched it about 50 yards down the road and twisted the front frame etc . really nice lookin car - shoulda kept the whole thing . shorly after picked up an engine and trans out of a 66 ( riv i think ) for spare parts . block:cleaned,checked,deburred,bored +.030 rods:checked,marked,mag'd,beams polished,arp bolts installed pistons:new cast fed-mog #69P30,installed on rods crank:checked,mag'd,deburred+,oil holes chamfered,polished-turning not needed assembly balanced and marked,dampner to flexplate heads:checked,deburred,valve job,guides,new kenne-bell dual valve springs part #KB10901 oil pump:new poston hi output #PE899713 also newoston rings,mains,rods,cam brgs-good ones $2300.00 - includes all nailhead parts i have - extra block,heads,manifolds(not 66 quad intake-sold it),'65 4bbl intake,covers,starters,water pump,timing cover(good shape)nut,bolts etc etc etc.some of the "extras" have just been sitting inside uncovered and will need some TLC but all main parts have been stored inside and boxed or covered etc. transmission:"switch" TH400,match to motor,redone by a good local shop using H.D. parts and set for firm shifts.new poston #PE3000 tq converter $850.00 - includes the extra matching spare TH400 trans out of the '66. $3000 - all prefer not to ship-can arrange to transport for gas $$+,or meet 1/2 way etc. shipping $$ not included in prices if needed.joe-you are not that far probably. *i think you will need gaskets/seals,rocker arm assy's,freeze plugs,carb,and misc replacements (water pump,starter,etc) as needed to finish motor.*i may have a line on a new K-B #113 hydraulic cam and K-B timing set if available-may want to figure $150.00 (?) extra for that if needed. thats it.thanks for the look.del
i checked - k-b cam and timing set probably not available at this time . and moved 401/trans info to its own thread . del
tom : rec'd payment today ( thur. ) in mail and with a little luck will get that out friday sometime . contact me if any problems . thanks . del
thats good - had to go to elmira friday , friend in hospital with mild stroke . working monday so parts out probably monday after work if time or tuesday at the latest . sorry for the delay . del
