Its In !!!!

Discussion in 'Small Block Tech' started by mhgs, Jun 5, 2010.

  1. mhgs

    mhgs it just takes money !!

    I finally got the new motor in today !!!!...whee hooo.....
    Got the shorty headers all in and bolted up and they fit great. WHope to have it running within the next week or so .........FINALLY !!!
     
  2. DaWildcat

    DaWildcat Platinum Level Contributor

    Looking forward to hearing more!

    Devon
     
  3. Jeff T

    Jeff T Just a 350... A Buick 350

    I can see the :) !! Congrats!!
     
  4. sean Buick 76

    sean Buick 76 Buick Nut

    Great I look forward to hearing more!
     
  5. mhgs

    mhgs it just takes money !!

    my build.....
    Block ....all oil mods, stress plate bored and honed, decked, ( now 11.1-1 ), all balanced w/ new balancer, rods maged and polished, arp bolts.
    Camshaft.....comp cams custom grind on a 110 center w the roller rockers 552,562-284,286
    Heads.....fully ported w/manley 192,155 valves ,bronze over size stem guides, roller rockers, isky springs, retainers, clips, manton 3/8 pushrods.

    Intake heavily modified poston , now a single plane with added height to a tunnel design all ported and matched to the heads.

    Custom fab shorty headers 1 7/8-2 inch primaries.

    hooked to a turbo 350 with mods and a coan 2800 stall converter.....to a 3.42 posi.......sure there s more but I am forgeting where all the money went.
    Will get some pics up tomorrow hopefully........
     
  6. Big Matt

    Big Matt Well-Known Member

    Nice!
     
  7. mhgs

    mhgs it just takes money !!

    just a couple pics....sorry I haven't had the time to get it running but .....It will.
    I had put the headers on and forgot to take some pics, so this is just the drivers side, but the other is much the same.
    you can see the new under drive pulleys I made too.
    http://s1021.photobucket.com/albums/af334/swannymh/buick/
     
  8. scott kerns

    scott kerns Silver Level contributor

    Did you throw it on a dyno? What are your expectations for the car/engine?

    Scott
     
  9. Dan Healey

    Dan Healey Well-Known Member

    Aluminum heads too, :Brow: what engine is it?
     
  10. Cali72's

    Cali72's Well-Known Member

    wowowowowowowoow nice man:shock: :shock:
     
  11. mhgs

    mhgs it just takes money !!

    nah....I wish those heads were aluminum , paint can do amazing things !!
    Did not put it on a dyno as I am basically a cheap guy I guess, besides, It could break on a dyno then I would really be pissed.....at least if it breaks now it will be me doing it . All the info put into the desk top dyno says 526 hp @ 6200......so if it breaks at 6200 I should be going pretty good.
     
  12. mhgs

    mhgs it just takes money !!

    my duration at .050 is 232,238......I agree with the converter stall, I will have to see how it goes but I am hoping that it will be a bit looser with the more powerful motor in there.
     
  13. 71skylark3504v

    71skylark3504v Goin' Fast In Luxury!

    Lovin the Aluminum heads.:Brow: What kind on flow numbers are your heads putting out?
     
  14. ubushaus

    ubushaus Gold Level Contributor

    You gettin' the itch Cason!?
     
  15. ubushaus

    ubushaus Gold Level Contributor

    I'm guessing this is the Burton Machine setup? What rockers did you go with (brand/ratio)?
     
  16. 71skylark3504v

    71skylark3504v Goin' Fast In Luxury!

    Nope! :laugh: My car still runs good:bla:
     
  17. sean Buick 76

    sean Buick 76 Buick Nut

    [​IMG]

    Looks like either Poston or TA roller rockers...
     
  18. sean Buick 76

    sean Buick 76 Buick Nut

    I just thought I would post the pics of everyone can see without going to the link...

    Great work!!!!

    [​IMG]

    [​IMG]

    [​IMG]
     
  19. mhgs

    mhgs it just takes money !!

    it really is a small block........
     
  20. sean Buick 76

    sean Buick 76 Buick Nut

    I really like the look of the painted heads!
     

Share This Page