I have NOS GM 1363429 (clutch equalizer to engine seal) how to repro?

Discussion in 'U-shift em' started by NZ GS 400, Mar 16, 2018.

  1. Brett Slater

    Brett Slater Super Moderator Staff Member

    I'll grab one.
     
  2. mikegs400

    mikegs400 Well-Known Member

    Sign me up !
     
  3. dl7265

    dl7265 No car then Mopar

    Yes ! Keep getting beat out on one to have re’poed . That dodge accordion one Sucks ...
     
  4. NZ GS 400

    NZ GS 400 Gold Level Contributor

    Thanks for letting me know. It looks like a bit of interest is here. Stay tuned!
     
  5. Brett Slater

    Brett Slater Super Moderator Staff Member

    How about these while we're at it?

    20180506_120332.jpg
     
    STAGE III and dl7265 like this.
  6. mikegs400

    mikegs400 Well-Known Member

    You can put me down for a set of those to go with the seal! Thank You
     
  7. Buicksky

    Buicksky Gold Level Contributor

    Interested in 2 of the seal only 485 to go ...
     
  8. NZ GS 400

    NZ GS 400 Gold Level Contributor

    Almost there! :) I am going to be visiting my family in the USA for a month. I haven't lost interest in this project.
     
    Dano likes this.
  9. Daves69

    Daves69 Too many cars too work on

    Bump! Any progress on this?
     
  10. mikegs400

    mikegs400 Well-Known Member

    I am waiting and hoping!
     
    Dano likes this.
  11. STAGE III

    STAGE III Lost Experimental 455-4 Bolt Main Block.

    Sign me up too please.

    Just a thought but when I wanted our Tri-Shield floor mats reproduced (unfortunately several different versions & I had to personally take their pre-orders as well as locate and supply a mint set of final agreed on version) I went to (in this case Legendary) to absorb the initial costs while the Buick troops amassed pre-orders.

    Obviously not a ton of Buicks with 4 speeds (any crossover to other GM's?) for part suppliers to salivate over depending just on us.

    Worse case scenario I will just make something that at least functions for my heap.

    Still hope we can come up with a reasonable supplier : )
     
  12. NZ GS 400

    NZ GS 400 Gold Level Contributor

    Hi Fritz and other interested folks,

    I still plan to pursue this. I have a new baby at home that has been drawing my attention and time lately! Thanks for the posts, they keep me motivated.
     
    Dano likes this.
  13. TXGS

    TXGS Paint by numbers 70 GS 455 4spd

    Im in
     
  14. Dano

    Dano Platinum Level Contributor

    I'm in no hurry, but would take a few.
     
  15. PGBuick

    PGBuick Well-Known Member

    I could use 2 Z bar seals - both ends if they exist
     
  16. Brett Slater

    Brett Slater Super Moderator Staff Member

    Any progress on this project?

    Todd Miller is selling the rest of the 4-speed setup and this would make a great addition.
     
    Dano likes this.
  17. ToddsGS

    ToddsGS Founders Club Member

    If I had those NOS pcs I would contact Steele Rubber products to see if they would repop them.....

    I have a guy there I work with that I can contact if the NOS pcs are still around to copy!?!
     
    Dano, Brett Slater and 69GS430/TKX like this.
  18. Max Damage

    Max Damage I'm working on it!

    I wonder if the person that 3D printed the mirror gasket could tackle the spark plug retainer too?
     
    BuickV8Mike, Dano and Brett Slater like this.
  19. Brett Slater

    Brett Slater Super Moderator Staff Member

    My sense tells me there'd be a pretty good market for these.
     
    Dano likes this.
  20. NZ GS 400

    NZ GS 400 Gold Level Contributor

    Sounds like a great plan Todd. I have 2 NOS. See what you can do and let me know.

    I need someone to drive this. I have too much going on right now. I will ship the part where it needs to go.
     
    Dano, ToddsGS, Daves69 and 1 other person like this.

Share This Page