1965 GRAN SPORT SKYLARK PARTS For Sale

Discussion in 'Parts for sale' started by bobbybuick, Sep 10, 2013.

  1. bobbybuick

    bobbybuick Well-Known Member

    Glad you like it! I cleaned the lens and polished it up a little before I sent it
    Thanks again and let me know if you need anything else
     
  2. Clanceman427

    Clanceman427 Hardtops need not apply

    Bob, the door panels came today. Packed nicely, no issues. Excited to put them on. My thought was to use the headliner glue like you recommended and re-glue the edges back to the backer board, using paint sticks (to spread the load even) on both sides of the door panel edges and some clamps- whatya think, is that what you'd do?
     
  3. bobbybuick

    bobbybuick Well-Known Member

    yes just make sure you wait to adhere it.you can spray it.then brush the places you miss with a brush.Also you could use fiberglass mesh or something like jbweld to repair the clip holes.
    spray both surfaces and wait 10 minutes or 15 minutes before you attempt to marry them together.I would use heavy corrugated cardboard on the vinyl side and a wooden stick on the back to hold and SQUEEZE CLAMPS

    after that spray them down with whesleys bleach white and scrub with a brush rinse with Hot water on a rag and repeat before you put on whatever vinyl treatment you use
    they will clean up nice with a little work
     
  4. tsollazo

    tsollazo Well-Known Member

    Any chance you have any bench seat parts? I am looking for the plastic sleeves that the seatbelts thread through and the plastic cover that goes over the center hinge base?

    Thanks,
    Tony
     
  5. Clanceman427

    Clanceman427 Hardtops need not apply


    Thanks for the tips Bob! Will do.
     
  6. bobbybuick

    bobbybuick Well-Known Member

    Sorry no bench seat parts
     
  7. Neils64skylark

    Neils64skylark Active Member

    65 skylark wiper switch with knob still up for grabs?
     
  8. bobbybuick

    bobbybuick Well-Known Member

    yes sir
     
  9. Neils64skylark

    Neils64skylark Active Member

    I pm you a few questions. Hope to hear from you soon
     
  10. crewser

    crewser Platinum Level Contributor

    Is that lower antenna mast a screw in or drop in base can't tell in the plastic.

    Jim C
     
  11. bobbybuick

    bobbybuick Well-Known Member

    the one on the wood strip in a drop in but eliptial mast the upper one is a screw in both are new
     
  12. bobbybuick

    bobbybuick Well-Known Member

    here is the wiper switch 5 bucks shipping will work
     

    Attached Files:

  13. schlepcar

    schlepcar Gold Level Contributor

    Bob,
    If still available,I need the decals and the retractable antenna. I bought the frame from you last year, Dan
     
  14. bobbybuick

    bobbybuick Well-Known Member

    Dan there are 2 antennas and one Base
    one is screw in one is push in elliptical and the base
    i have Both and the decals
     
  15. schlepcar

    schlepcar Gold Level Contributor

    Which one will go in the base you have? Are there any port vents still available?
     
  16. bobbybuick

    bobbybuick Well-Known Member

    Only the elliptical will fit the base no on the vents
     
  17. schlepcar

    schlepcar Gold Level Contributor

    What will be the total to ship to Michigan for the base,mast and decals?
     
  18. bobbybuick

    bobbybuick Well-Known Member

    Send me zip I'll box up tomorrow and give you a total you want the base too
     
  19. schlepcar

    schlepcar Gold Level Contributor

    Yep,
    Base,mast,decals.....to 48658. Let me know if you have paypal or how you want payment,Dan
     
  20. bobbybuick

    bobbybuick Well-Known Member

Share This Page