Here is a Buick 350 (369 cubes) that is 422 HP NA with low compression and 630 hp with a few PSI of boost: http://www.youtube.com/watch?v=zktYY...KuiWwBNoTF8XxC Here is a 1021 HP Buick 350 with stock ported intake, ported heads and only 355 CID: http://www.v8buick.com/index.php?threads/1021-hp-from-buick-350-ran-8s-in-the-quarter.210988/ Here is a 10:1 compression Buick 350 that was 551 HP NA http://www.v8buick.com/index.php?threads/shes-alive.40660/ Some old circle track Buick 350 info about some 580 HP NA engines as well more info later in the thread about a Buick 350 powered car that ran 11.07 in the quarter. http://www.v8buick.com/index.php?th...d-the-circle-track.239729/page-3#post-2076442 Nitrous on a stock 350: http://www.v8buick.com/index.php?threads/stock-buick-350-skylark-runs-12s-in-the-quarter.224070/ Then there are the guys running the stock class Buick 350s with stock carbs, stock intake, no head porting, stock lift on the cam etc and are in the mid 11s. http://www.v8buick.com/showthread.php?t=215851 Here is a twin turbo buick 350 that is about 550 HP with no internal mods other than a custom camshaft. http://www.v8buick.com/index.php?th...t-has-begun-i-had-to-salvage-this-car.168371/ 350 in the mid 12s: http://www.v8buick.com/showthread.ph...hlight=nitrous That should get you started, and next time try to post a SBB question in the SBB section as you will get more response... __________________ Turbo buick 350 homemade!! http://www.v8buick.com/showthread.php?t=99527&highlight=alive Instructions on how to change rear seal. http://www.v8buick.com/showthread.php?t=115596&highlight=alive 350 head project with flow #'s! http://www.v8buick.com/showthread.php?t=120529&highlight=heads head year differences http://www.v8buick.com/showthread.php?t=122404&highlight=heads The 546 hp Buick 350 without power adder http://www.v8buick.com/showthread.php?t=40660&highlight=alive Our plight for heads... http://www.v8buick.com/showthread.php?t=89031&highlight=alive Nitrous at the track! http://www.v8buick.com/showthread.php?t=73182&highlight=alive TA intake http://www.v8buick.com/showthread.php?t=50141&highlight=alive Head swapping http://www.v8buick.com/showthread.php?t=57460&highlight=350+heads 9 Mark Burton goes Fast with class, so call Burton Machine today for your Custom Buick 350 parts or builds 10.*Valvecovers I really like the tall Poston valvecovers in Black!: http://www.postonbuick.com/eshop/10Expand.asp?ProductCode=PE90734 Intakes- T/A, Poston, and Burton... 11*Any other suppliers yet? Any dyno runs? GS Johnny, Darren Gun and Hector as well have put in great showings, with Hectors being a dual plane air gap!!!!! http://www.buickperformancegroup.com/forums/showthread.php?t=6012 The amount of hard work and decication to build a 350 intake is mind boggling! Pat on the back to Hector, Johnny, and Mark. For anyone who does not know this already, Darryl welded up the alum singleplane inthe 80s that was used on the 551 hp Rob margel engine. Also Darryl and his Buddy were shoooting nitrous on 350s that made over 500 HP NA! Headers- T/A and Hooker 12*Are both still available? Any flange kits available for custom apps? Flange kits for the Buick 350 are ordered at Burton Machine then add any custom header to his BEEFY flanges 509-860-3370 or Poston wil also make the headers in 2" for a little extra over regular headers. 13.*Ignition- HEI, or a petronix? For the ignition the HEI re-curved is fine for under 350 HP but above that use an MSD dist complete or the following top quality performance ignition. Mark has had GREAT luck with a Pertronix as well so do not count that out for a cheeper solution with the old points style apearance. Another way is to have daves smallboddies build you a dist. This is what I am going to use: MSD Cap and Rotor Kit For GM V8 HEI 121-8416 HEI Low Resistance Bushing 121-8412 Extreme HEI Coil Dust Cover With Wire Retainers External Mounted Coil 121-84011 Digital-6 Plus Ignition 121-6520 Blaster HVC Coil 121-8252 14*Anything new to report in this department? Oiling system-TA sells a drill bit to enlarge passages, we can use the oversized TA pickup, adjustable regulator, order new front cover from anywhere even parts stores, a dry sump setup is in the works in my brain at least....Grooved cam bearings, baffle added to oil pan some other little tricks 15*Bring me up to date on the hot modifications Timing cover-order one or use a good used one 16*Still readily available new Harmonic ballancer-do not use v6 ballancer, TA will get you setup with the right ballancer upon request I think 17*Still available new? Any trick pieces available yet? 18*Headgaskets Gessler has steel shims in stock for the 350, Gaskets-to-Go made us multilayered gaskets and will make another run once enough more people need them even though Cometic wants a minimum of well over 20 before it would consider it. The Gaskets to go were great to work with and offered flexable ordering and custom options like different bores without extra cost. Now we have re-usable head gaskets in ANY bore size, height, ect for any modified 350 application. http://www.v8buick.com/showthread.php?t=157851&highlight=gaskets Nitrous run videos! Nicks car in the mid 12s has stock intake, heads, cam, manifolds, no rebuild all stock! while Guys car has a fully built 350 that has been running hard since the 90s without a rebuild! http://www.v8buick.com/showthread.php?t=167545 Marks Turbo car: Go 350 Movement![/quote]
well this thread is technicaly stickied via hot linked on the 350 performance parts and services thread!:gp:
Deleted by the original poster, as is his perogative. BBBBIIIILLLLMMMMAAAAAHHHHHHHH! why you wanna do us like that, mang? is the magazine article finally going to come out?