Wanted 69 Buick electra225

Discussion in 'Parts wanted' started by scubasteve455, Sep 8, 2020.

  1. scubasteve455

    scubasteve455 Well-Known Member

    Rt frt fender mouldings
    Rt frt door mouldings
    in good shape.
     
  2. GSX 554

    GSX 554 Gold Level Contributor

    2 door or 4 door ???
     
  3. scubasteve455

    scubasteve455 Well-Known Member

    4-door. All the mouldings are needed
     
  4. newmexguy

    newmexguy Well-Known Member

    Have a lot of Coupe mouldings. Guess the only one I have that might interchange is the pot metal that goes around the rear skirt
     
  5. scubasteve455

    scubasteve455 Well-Known Member

    It’s a shame no one has responded. This is a very nice car. That needs parts. It was wrecked
     
  6. scubasteve455

    scubasteve455 Well-Known Member

  7. scubasteve455

    scubasteve455 Well-Known Member

  8. scubasteve455

    scubasteve455 Well-Known Member

    mixed solvent based. Color was not close. Then mixed Waterborne. Dead Balls On.
    Go figure.
     
  9. scubasteve455

    scubasteve455 Well-Known Member

    Car is sooo nice. I put flatting base in the clear. To match the lacquer. So the Fender and door was not to shinny
     
  10. 1969RIVI

    1969RIVI Well-Known Member

    Last edited: Sep 13, 2020
  11. scubasteve455

    scubasteve455 Well-Known Member

    Thanks . But doesn’t look like that car has any side moulding . Wheel house and rocker might
     
  12. GSX 554

    GSX 554 Gold Level Contributor

    I believe 69 and 70 were the same .
     
    bill lagna likes this.
  13. scubasteve455

    scubasteve455 Well-Known Member

    I believe the mileage is 32,000. To Bad I getting no hits on parts
     
  14. jj5794

    jj5794 Well-Known Member

    The front fender and the door rocker moldings were different on the 1969 and 1970 Electra 225's.

    For such similar model years the number of differences in parts, including trim parts, is remarkable.

    Hope this helps.

    Jim Vesely
    ROA # 7437
    BCA # 39477
     
  15. GSX 554

    GSX 554 Gold Level Contributor

    That is for the lower moldings . I think the side spear moldings were the same in 69 and 70
     
  16. jj5794

    jj5794 Well-Known Member

    Yes. I was referring to the moldings along the bottom of the front fenders as well as the rocker moldings below the doors..

    Jim Vesely
    ROA # 7437
    BCA # 39477
     
  17. scubasteve455

    scubasteve455 Well-Known Member

    Well my alternative . Stick on vinyl to go up the middle of the panel. Been looking all over else where. oh well.
     
  18. newmexguy

    newmexguy Well-Known Member

    A rare rainy day in Phoenix. Believe they have moved their main yard farther north, out of Metro Phoenix. Farther N along the Black Canyon Frwy - Interstate 17. Must have been a logistics nightmare. Guessing they crushed a lot of marginal stuff.
    If you were in search of two door stuff, could have fixed you up. Have had it (trims) going on four years, big car stuff is a LOT harder to find buyers for. These are old pics from four years ago, did recently sell the Windshield surround trims. Pics are just to show the excellent conditions, that is the reason pulled them off the car. Did also sell the front wheel opening trims.
     

    Attached Files:

    Last edited: Sep 18, 2020
    scubasteve455 likes this.
  19. scubasteve455

    scubasteve455 Well-Known Member

    Thank you Nailhead
     

Share This Page