Big Block Driveshaft

Discussion in 'Parts wanted' started by OhioGS400, Apr 27, 2010.

  1. OhioGS400

    OhioGS400 Well-Known Member

    WTB Original driveshaft for a 68 GS 400. Must be strait and in-phase. Thanks very much.
    Randy
     
  2. OhioGS400

    OhioGS400 Well-Known Member

  3. Buizila

    Buizila GO BROWNS !!!!!!

    Randy,does it have to be original? I have a really nice one that I had custom clutch in downtown Cleveland make me yrs ago. No pits very smooth and it's bare. Has a new 400 yoke and spicer u-joints all installed. Not to mention I'm local to ya. Let me know if ur interested?
     
  4. OhioGS400

    OhioGS400 Well-Known Member

    Mike- sent you a PM- thanks.
     
  5. OhioGS400

    OhioGS400 Well-Known Member

  6. OhioGS400

    OhioGS400 Well-Known Member

  7. Thumper (aka greatscat)

    Thumper (aka greatscat) Well-Known Member

    Randy,did the pic I sent you help?
    ghary
     
  8. OhioGS400

    OhioGS400 Well-Known Member

    Gary- Yes, thanks very much. It's tapered at both ends, correct?
    Randy
     
  9. Thumper (aka greatscat)

    Thumper (aka greatscat) Well-Known Member

    Yep,and its 3" diameter in the center section.I can try to find you one in BG if you'd like.
    gary
     
  10. OhioGS400

    OhioGS400 Well-Known Member

    Gary- that would be great- thanks very much.
    Randy
     
  11. OhioGS400

    OhioGS400 Well-Known Member

  12. OhioGS400

    OhioGS400 Well-Known Member

  13. OhioGS400

    OhioGS400 Well-Known Member

  14. OhioGS400

    OhioGS400 Well-Known Member

  15. weim55

    weim55 Well-Known Member

    I have one from a '70 GS 455 with a turbo 400, do you think it will work?

    Steve weim55 Colorado
     
  16. OhioGS400

    OhioGS400 Well-Known Member

    Steve-that should work. PM sent.
    Thanks.
     
  17. carmantx

    carmantx Never Surrender

    Randy, question for you. We have several shafts sitting around, and will try to find something today.

    I know we have TH400 shafts that have different diameter input shafts going in to the tranny. We have had to change the tail piece on our race car tranny to fit the shaft we had built for it. So if what you need is the smaller diameter input, we might be able to find one here.
     
  18. OhioGS400

    OhioGS400 Well-Known Member

    Steve- you need to clean out your PM mailbox- I can't send you a PM.
    Please measure your driveshaft cap to cap and let me know the length so we can see if it will work. email me: randmunn1@yahoo.com
    Thanks very much.
    Randy
     
  19. OhioGS400

    OhioGS400 Well-Known Member

    Mark- The trans input shaft I have is 1 7/8"dia and 4 7/8" long. The yoke is 3 5/8" outer width, 2 1/2" inner. It takes a external-type 'C' clip
    u-joint. The driveshaft I need is one-piece (no rubber dampner) with the main shaft dia. 3"- the type used on the BBB cars. My cap to cap length is 54 3/8" with the input shaft fully inserted in the trans.
    Thanks very much.
    Randy
     
  20. OhioGS400

    OhioGS400 Well-Known Member

Share This Page