400-430-455 REUSABLE Molded Rubber Valve Cover Gaskets

Discussion in 'Products and Services' started by TABuickMike, Jul 18, 2020.

  1. TABuickMike

    TABuickMike Michael Tomaszewski Jr

    THE LAST SET OF VALVE COVER GASKETS YOU'LL EVER NEED!!

    That's right! For the first time ever, reusable valve cover gaskets are now available for the 400-430-455 big block Buick engines. These are THE BEST valve cover gaskets EVER offered for our engines. Constructed from 3/16" thick nitrile rubber molded around a steel spine with torque limiters at each bolt hole that prevent over-tightening which can crush or split cork gaskets and cause leaks. The days of using old outdated cork valve cover gaskets that leak and tear are over!! These will ensure a perfect seal every time for years to come. Perfect for those who dislike cork or rubber gaskets that weep oil, or racers who have to remove the valve covers often.

    TA 1702-455D ... Introductory price $53.00

    108952927_3225657987455574_3586892592116320186_o.jpg 107764656_3225658140788892_1209513623082468181_o.jpg 113999572_3225658400788866_4927005772171730288_o.jpg
     
    schwemf, slimfromnz, Sasha and 7 others like this.
  2. Chi-Town67

    Chi-Town67 Gold Level Contributor

    How long is the introductory price good for Mike?
     
  3. Gary Bohannon

    Gary Bohannon Well-Known Member

    Are they thick enough for use with original Buick valve covers on your aluminum heads?
     
  4. Briz

    Briz Founders Club Member

    will they seal factory stamped valve covers? Also, are they thick enough to raise stock covers enough to used roller rockers?
     
  5. thebuick

    thebuick Well-Known Member

    good question Briz if so I will buy a set
     
  6. TABuickMike

    TABuickMike Michael Tomaszewski Jr

    I don't have a time frame off hand.

    Yes/no, you would need to belt sand the lip of the valve cover to make it a little thinner, or bend it outwards to fit.

    They will work just fine with stamped steel valve covers on iron heads. See my above answer for use on TA aluminum heads. They are not thick enough to clear roller rockers.

    Stamped steel valve covers on TA aluminum heads require a 1/4" gasket (or a standard gasket if you belt sand the lip of the valve cover) to clear roller rockers.
    Stamped steel valve covers on iron heads require a 3/8" gasket to clear roller rockers.
    Note: High lift cams might require even more clearance.
     
    Last edited: Jul 21, 2020
  7. LARRY70GS

    LARRY70GS a.k.a. "THE WIZARD" Staff Member

    Mike, any issues using this gasket with aftermarket cast aluminum valve covers like the ones you sell or the old Poston covers on the TA aluminum heads?
     
  8. TABuickMike

    TABuickMike Michael Tomaszewski Jr

    Nope, there's a picture above showing fitment using it with our heads and valve covers. Fits perfectly and looks beautiful.
     
  9. LARRY70GS

    LARRY70GS a.k.a. "THE WIZARD" Staff Member

    Just ordered 2 sets.
     
  10. LARRY70GS

    LARRY70GS a.k.a. "THE WIZARD" Staff Member

    Mike, any instructions with these? I normally use black weatherstripping cement and glue the gasket to the cover. No sealant between the gasket and head.
     
    Postsedan likes this.
  11. Postsedan

    Postsedan 13427 L78

    Excellent Question Larry :)
     
  12. Bens99gtp

    Bens99gtp Well-Known Member

    I would assume with this style it would be install dry and torque to spec
     
    1973gs and 71gs3504sp like this.
  13. 71gs3504sp

    71gs3504sp Well-Known Member

    I would assume to that it should be installed dry. Just like my 1999 Grand Prix it has a GM reusable gasket for the transmission pan. I just replace the fluid yesterday and reinstalled the gasket dry. BTW it's now 21 years old and transmission pan is always dry and never a leak so far!
     
  14. LARRY70GS

    LARRY70GS a.k.a. "THE WIZARD" Staff Member

    Yes my 98 Riv as well. They work very well. OK, no sealant at all then, makes things even easier. These gaskets look great, they were delivered yesterday.
     
  15. TABuickMike

    TABuickMike Michael Tomaszewski Jr

    I would install them as-is.
     
  16. LARRY70GS

    LARRY70GS a.k.a. "THE WIZARD" Staff Member

    Thanks Mike, looks like a quality piece.
     
  17. 1969RIVI

    1969RIVI Well-Known Member

    Mike, if I order a set and ad it along with a bunch of valve train parts plan on ordering within the next month would I qualify for the introductory pricing?
     
  18. stagedgs

    stagedgs 1967 GS400

    I just received my set of TA 1702-455D gaskets, it IS a very nice piece. Thanks, Mike.

    Could a one piece oil pan gasket of similar construction be in the works?
     
    bostoncat68 and Tom Righter like this.
  19. Tom Righter

    Tom Righter Well-Known Member

    Nice product Mike.Its good to move into the 21st-century!
     
    BUICKRAT likes this.
  20. Tom Righter

    Tom Righter Well-Known Member

    Timing chain cover gasket next?
     
    1973gs likes this.

Share This Page