PARTING OUT 1967 SKYLARK 2 Door

Discussion in 'Parts for sale' started by RACEBUICKS, Aug 6, 2009.

  1. JimJames

    JimJames Well-Known Member

    Looking for 2 hood springs if good. Thanks. Jim
     
  2. Revenant

    Revenant Janissary of Junk

    Hey still have parts left? I need about 1/3 of the passenger quarter panel if you're willing to chop it. From about, mid wheel well back. Also looking for a trunk lid (Don't care if it's rusted so long as it's straight) and a rear bumper.

    Need the trunk latch as well, not the part on the lid, the part in the trunk itself.
     
  3. 67 Post GS

    67 Post GS Well-Known Member

    If you cut the passenger quarter panel? I need from mid wheel to door. Skin only. Thanks Ron
     
  4. ubushaus

    ubushaus Gold Level Contributor

    Hey Mike,

    If you decide to tear apart the rear end, I need a useable axle shaft. Does anyone know if the convertible shafts were beefier than the coupes?

    Thanks,
     
  5. RACEBUICKS

    RACEBUICKS Midwest Buick Mafia


    Hinges? make me an offer.

    I got this and once again wil entertain offers


    Here is the pictures of what I have

    I have a 4 door I can pull an axle from They are all the same as far as I know. I have been selling axles for $40 plus shipping. Which side did you want?
     

    Attached Files:

  6. ubushaus

    ubushaus Gold Level Contributor

    Not sure if the side matters to me. I may take both sides to have backup.

    The reason I asked if there were differences is that I recently bought a '66 axle that seems to be tapered significanlty thinner toward the splines. The axles that came out of my '67 convertible were not tapered and seemed to be the same thickness all the way to the seal. The idiot at the machine shop I had pull the bearings left me with a nice gouge on the seal surface.

    Can you snap a few pics including a close up shot at the inner splines?

    Thanks,
     
  7. JimJames

    JimJames Well-Known Member

     
  8. RACEBUICKS

    RACEBUICKS Midwest Buick Mafia

    here are the splines
     

    Attached Files:

  9. sparkybuick

    sparkybuick Active Member

    Hey Mike,
    Do you still have the trunk letters? Also looking for the grommet between the power booster and the master cylinder. Have a pic if you need to see what I am looking for. Thanks
     
  10. RACEBUICKS

    RACEBUICKS Midwest Buick Mafia

    Have to look next week.
     
  11. ubushaus

    ubushaus Gold Level Contributor

    Hey Mike,

    Those may be it. See the attached photo. The axle on the right measures 1 1/16 where the caliper is. The one on the left (from the '67) measures 1 3/16 at the same location. Can you let me know what yours measure? And can you estimate shipping for both to 33407 (West Palm Beach, FL - business address)?

    Thanks!
     

    Attached Files:

  12. 67 Post GS

    67 Post GS Well-Known Member

    Ill Pass on 1/4 panel. Thanks Ron
     
  13. RACEBUICKS

    RACEBUICKS Midwest Buick Mafia

    both Mine measures 1.193
     
  14. ubushaus

    ubushaus Gold Level Contributor

    OK Mike,

    I know I am bordering on annoying (if not already there), but can you confirm that the seal surface is ok on both of them, and that they have the rw-507-cr bearing installed? Also, can you quote shipping to 33407 West Palm Beach, FL for both?

    Thanks,
     
  15. RACEBUICKS

    RACEBUICKS Midwest Buick Mafia

    $35 for the shipping And I cant see any seal here is what I see. The bearings are in excellent condition as far as I rolled them and feel nothing that would say they are bad. No wobble or looseness
     

    Attached Files:

  16. Revenant

    Revenant Janissary of Junk

    Still have the Manifold? If so let me know a price on that and the rear bumper shipped to 93722

    Also, have you got the keys for the door and trunk locks? If so give me a price on the locks and keys as well.
     
    Last edited: Oct 2, 2009
  17. gatkins2004

    gatkins2004 65spec401 frost bitten

    Hello, i'm interested in the inner door panels. Can you send pics of both sides?

    Thank you,
    Gary
     
  18. RACEBUICKS

    RACEBUICKS Midwest Buick Mafia

    The engine is complete and it runs Im selling it that way. Rear bumper is bent you saw that right?

    Will see what I can do about getting pictures today for you.
     
  19. Revenant

    Revenant Janissary of Junk

    Cancel my order on the bumper. Found a whole parts car I'mma pick up tomorrow.
     
    Last edited: Oct 2, 2009
  20. 197064buickspec

    197064buickspec 1964 Special Post-455

    Mike,

    What would you be looking to get for the arm rest backing plates? and the seat belts if they are for sale?

    Brian
     

Share This Page